Skip to content
Fleet Scanner
Hardware integration · Teltonika FMC234

Teltonika FMC234 battery tracker, working inside Fleet Scanner

The Teltonika FMC234 is a 4G LTE Cat 1 GPS tracker with a 1000 mAh battery inside a water-resistant IP67 case. Teltonika made it for stolen vehicle recovery, trailers, insurance and building machines. If a thief cuts the power, it can keep going for days on its own battery. Fleet Scanner, running on your own server, turns its data into a live map, alerts and reports.

4G LTE Cat 11000 mAh batteryIP67 water-resistant casePort 11922
Illustration of the Teltonika FMC234 GPS tracker
1000 mAhbattery
8 dayson battery in ultra deep sleep
5satellite systems (GPS, GLONASS, Galileo, BeiDou, QZSS)
422,400records kept in 128 MB
10 to 30 Vpower range
live_position · LTE Cat 1
4GSpeed 54 km/h
01 · Live tracking · Every record

FMC234 GPS tracker on the live map over 4G

The FMC234 reads five satellite systems through an antenna hidden in its case. It sends the position, speed and engine state over the 4G LTE Cat 1 network. Out of coverage, it can hold about 422,400 records in its 128 MB memory and send them when the signal is back. Your Fleet Scanner map then shows the whole trip with no gaps.

Position Speed Ignition (engine on/off) Movement
GPS fleet tracking software →
battery · 1000 mAh68%
Main power cutBattery running
02 · Battery life · Internal battery

A battery tracker that lasts days without power

Teltonika says the 1000 mAh battery runs the FMC234 for about 10 hours with sleep turned off and a report every hour. In deep sleep with hourly reports, it lasts about 4 days. In ultra deep sleep, when it sends nothing, it lasts about 8 days. Real results depend on your settings and the signal. Fleet Scanner shows the vehicle voltage and the battery voltage in every record.

External voltage Battery voltage Battery current Sleep mode
Real-time fleet alerts →
theft · recovery
Towing
03 · Stolen vehicle recovery · Events + outputs

Towing, jamming and engine block for theft cases

When the engine is off, the FMC234 can tell if the vehicle is lifted at an angle or towed away. It reports GNSS jamming as a warning or a critical state. With a relay on an output, it can stop the engine from starting until an approved iButton key or Bluetooth beacon is found. Teltonika says the FMC234 is used in Kiwa SCM certified anti-theft solutions built with a partner.

Towing GNSS jamming Unplug detection Immobiliser Auto geofence
Geofence alerts for vehicles →
driving · accelerometerX -612Y 180Z 990
Harsh braking
04 · Driver behaviour · Accelerometer

Harsh driving and crash records

The FMC234 saves a record when braking, speeding up or cornering goes past the limits you set. If crash detection is on, it watches the force on each axis to spot an accident. It can also keep a short trace of the moments around a crash. Fleet Scanner turns these records into alerts and a score for each driver.

Harsh acceleration Harsh braking Harsh cornering Crash detection
Driver scorecards →
sensors · Bluetooth 4.0
Cargo 6 °CDoor closed
05 · Cargo and trailers · Bluetooth LE

EYE Sensors for cargo, EYE Beacons for trailers

Bluetooth 4.0 LE lets the FMC234 read Teltonika EYE Sensors for cargo temperature, humidity and door state. An EYE Beacon can name a trailer or a driver without wires. The tracker also works with Bluetooth OBD-II dongles. Fleet Scanner stores each reading with the trip, and the battery keeps the readings coming while a trailer stands unpowered.

Bluetooth temperature Bluetooth humidity Door state Beacon ID
Trailer and container tracking →
inputs · outputs · 1-WireDIN1 Ignition ONAIN1 12.4 VDOUT1 Relay OFF
Input 2 on
06 · Wired extras · Inputs and outputs

Inputs, outputs, 1-Wire and a CAN adapter

The FMC234 has 3 digital inputs, 1 negative input, 2 impulse inputs and 2 analog inputs. Its 3 outputs carry up to 0.5 A each. A 1-Wire port takes driver keys and temperature probes, and there is an input for a Teltonika CAN adapter. Fleet Scanner logs every input change and can alert you about it.

Digital inputs 1 to 3 Analog inputs 1 and 2 Outputs 1 to 3 1-Wire CAN adapter
Fleet reports and dashboards →

FMC234 specifications

Network4G LTE Cat 1, made in two module versions with different band lists
SatellitesGPS, GLONASS, Galileo, BeiDou and QZSS, internal antenna, tracking sensitivity -165 dBm
Power+10 to +30 V DC
Battery1000 mAh, about 10 hours (sleep off), 4 days (deep sleep) or 8 days (ultra deep sleep) by Teltonika figures
Inputs and outputs3 digital inputs, 1 negative input, 2 impulse inputs, 2 analog inputs, 3 outputs (0.5 A each)
Extras1-Wire, CAN adapter input, Bluetooth 4.0 LE
Memory128 MB, about 422,400 records
ProtectionIP67, case with click-type two-phase closing
Size and weight70.5 x 67.0 x 25.6 mm, 91.8 g
Working temperature-20 to +60 °C with the battery; the battery charges from 0 to +45 °C
Fleet Scanner port11922

Specifications can differ between hardware revisions. Check the manufacturer’s datasheet for your exact unit.

How to connect the FMC234 to Fleet Scanner

  1. Put the SIM in while the FMC234 is not powered. Close the case fully and keep the cable connected so it stays IP67. Then wire power (10 to 30 V), ground and ignition.
  2. For the FMC234 setup on a laptop, open the Teltonika Configurator. Type in the APN from your SIM card, then your Fleet Scanner server address with port 11922 over TCP.
  3. Or set it up with SMS commands. If the tracker has no SMS login, type two spaces first, then: setparam 2001:APN;2002:APN_username;2003:APN_password;2004:Domain;2005:11922;2006:0. Here 2006:0 picks TCP.
  4. In Fleet Scanner, add the tracker by its IMEI number, pick the vehicle or trailer, and check that it shows on the live map.

Teltonika FMC234 FAQ

Does Fleet Scanner support the Teltonika FMC234?

Yes. Fleet Scanner reads its position, engine state, power and battery data, harsh driving and crash records, towing and jamming events, Bluetooth sensors and wired inputs. Send its data to port 11922 on your Fleet Scanner server.

How long does the FMC234 battery last?

Teltonika gives three figures for one charge: about 10 hours with sleep off and a report each hour, about 4 days in deep sleep with hourly reports, and about 8 days in ultra deep sleep with no reports. Your settings and signal change the result.

What is the difference between the FMC234 and the FMC230?

Teltonika describes the FMC234 as its FMC230 with a bigger battery. The larger 1000 mAh battery is what lets it keep working for days after the power is cut.

Which FMC234 SMS commands set the server?

The setparam command, using Teltonika’s parameter numbers: 2001 to 2003 for the APN name, user and password, 2004 for the server, 2005 for the port and 2006 for TCP or UDP. The getinfo command asks the tracker for its system information. The FMC234 manual on Teltonika’s wiki lists the rest.

FMC234 sealed and fitted. Your fleet on one map.

From a single tracker to a mixed fleet across 1,000+ device models: live tracking, alerts, fuel, drivers, maintenance and reports in one self-hosted platform. See it with your own hardware.

Get a free demo

More supported GPS trackers

Data names follow Teltonika’s FMC234 documentation; AVL IDs are not shown because we could not confirm them for this model. Battery times are Teltonika figures. Teltonika and FMC234 are trademarks of Teltonika Telematics. Specifications from the Teltonika FMC234 datasheet and wiki, and Teltonika’s FMC234 news release.

Take Control with
Fleet Tracking

Track vehicles in real time, optimize routes, and take full control of your fleet operations.

Free Demo