Skip to content
Fleet Scanner
Hardware integration · ATrack AK7S

ATrack AK7S GPS tracker, working inside Fleet Scanner

The ATrack AK7S GPS tracker is a small 3G box that you wire into a car, van or truck. It weighs 63 g and finds its place with both GPS and GLONASS satellites. It sends its reports over 3G, and it also has 2G GSM bands. ATrack built it around an event engine, so you choose what the tracker does when certain things happen on the road. Fleet Scanner runs on your own server and shows every AK7S report on a live map, with alerts and a full trip history.

3G UMTS/HSPA plus GSM bandsGPS + GLONASS 72 channels1-Wire driver ID and temperaturePort 21655
ATrack AK7S GPS tracker, a green box with status lights, an antenna socket and mounting ears
160,000logs kept in memory
3digital inputs, at most
2digital outputs, at most
4 mAin deep sleep at 12 V
63 gtotal weight
report · real time
Fix GPS + GLONASSStored 0 logs
01 · Live tracking · GPS and GLONASS

Real-time tracking with a big memory for dead zones

The AK7S uses a 72 channel receiver that listens to GPS and GLONASS. ATrack gives its accuracy as 2.5 m (CEP 50%). You set how often it reports. When the truck drives where there is no mobile signal, the tracker keeps its logs, up to 160,000 of them, and sends them later. Each saved point lands on the Fleet Scanner map, so the route has no gaps when you replay it.

GPS + GLONASS SBAS: WAAS, EGNOS, GAGAN, MSAS Report interval Stored logs
Live GPS vehicle tracking →
engine · event rulesX -612Y 180Z 990
Rule matchedAction report sent
02 · Event engine · Event control engine

Your own rules for what the tracker does

ATrack calls this the intelligent event control engine. You put several vehicle conditions together into one rule. Then you pick the action the tracker takes when they all happen. This lets one AK7S fit many kinds of jobs. Fleet Scanner saves the events it sends and can raise an alert on any of them.

Conditions Actions Combined rules
Alerts and remote commands →
sensor · 3-axissleepmoving
Moving yesImpact none
03 · Motion and impact · Accelerometer

Motion and impact from a built-in 3-axis sensor

Inside the AK7S is an accelerometer, a sensor that feels movement in three directions. It measures up to 16 g. Its job, in ATrack’s words, is motion and impact detection: it notices when the vehicle starts to move or takes a hit. Fleet Scanner turns these movement events into trip records and impact alerts.

3-axis ±16 g range Motion Impact
Driver behaviour reports →
1-wire · driver idA3 41 9F 00
Driver tag readTrailer linked
04 · Driver ID · 1-Wire interface

Know which driver is behind the wheel

The 1-Wire port reads a driver tag. ATrack offers an iButton reader, a magnetic iButton reader, an RFID reader and an active RFID reader, each with tags. There is also a 1-Wire trailer ID, so you can see which trailer is hooked up. Fleet Scanner links each trip to the driver who logged in.

iButton Magnetic iButton RFID Active RFID Trailer ID
Driver management software →
1-wire · temperature
Cargo 4 °C
05 · Temperature · 1-Wire temp probe

Temperature from a probe on the same 1-Wire port

ATrack also sells a 1-Wire temperature probe for the AK7S. Put it in a fridge van or a cargo box and the tracker can send the reading with its reports. Fleet Scanner draws the temperature on a chart and warns you when it goes too high or too low.

1-Wire temp probe Reading in each report
Cold chain tracking →
io · inputs / outputsDIN1 Ignition ONAIN1 12.4 VDOUT1 Relay OFF
Ignition ONTrip Business
06 · Inputs, outputs and relay · Molex 6 pin

Ignition, inputs, outputs and a 0 to 40 V analog line

All the wires go into one 6 pin Molex plug. There is one positive ignition input. The other pins can be set up as up to 3 digital inputs, up to 2 outputs and one analog input that reads 0 to 40 V. ATrack’s add-ons for these pins include a 12 V or 24 V relay, an SOS push button and a switch that marks a trip as business or private. Fleet Scanner shows each input and lets approved users switch the outputs.

Ignition input Digital inputs Outputs, 300 mA max Analog 0 to 40 V SOS button Business / private switch
Vehicle and equipment protection →
rs232 · add-ons
Adapter AC1PLink OK
07 · OBD, J1939 and add-ons · RS232 port

Add OBD-II, J1939, cameras and Garmin through RS232

The AK7S has a 4 pin RS232 port that also gives 5 V power to what you plug in. ATrack lists two diagnostic adapters for it, the AC1P and AC1R, for OBD-II and J1939 vehicles. The same port takes an RS232 expander, an RS485 adapter, two CMOS cameras, a Garmin navigator (FMI 2.0) and Squarell FLEX and SOLID units. What data you get depends on the add-on and the vehicle.

AC1P / AC1R OBDII_J1939 RS232 expander RS485 adapter CAM7570 / CAM5650 Garmin FMI 2.0
Preventive maintenance scheduling →

AK7(S) specifications

Network (AK7S-UG, global)3G UMTS/HSPA 800/850/900/1900/2100 MHz; GSM 850/900/1800/1900 MHz
DataUDP/IP, TCP/IP and SMS
GNSS72 channel GPS and GLONASS; SBAS: WAAS, EGNOS, GAGAN, MSAS; accuracy 2.5 m CEP 50%
GNSS sensitivityTracking -167 dBm, acquisition -148 dBm
AntennasBuilt-in cellular antenna; external GPS antenna on an SMA socket
Inputs and outputs1 positive ignition input; up to 3 digital inputs, up to 2 digital outputs (300 mA max sink) and up to 1 analog input (0 to 40 V, 12 bit), set by configuration
1-Wire1 port for driver ID and temperature sensors
Sensor3-axis accelerometer, ±16 g
Power12 V or 24 V vehicle system; 70 mA at 12 V while running, 4 mA at 12 V in deep sleep
Backup batteryOptional 3.7 V, 650 mAh
Memory16 Mbit flash, up to 160,000 logs and up to 9,000 queues
Connectors6 pin Molex for I/O, Mini SIM (2FF) socket, 4 pin RS232 accessory port with 5 V power, RS232 setup port
LEDs3 (power, GPS, cellular)
Size / weight95 x 48 x 26 mm, 63 g, flame retardant ABS+PC case, screw or adhesive mount
Operating temperature-40 to +85 °C without the battery, -20 to +60 °C with it
Setup and updatesSettings by ADM, SMS or RS232 cable; firmware by ADM, FOTA (over the air) or RS232 cable
CertificationsFCC, CE
ProtocolATrack protocol family
Fleet Scanner port21655

Specifications can differ between hardware revisions. Check the manufacturer’s datasheet for your exact unit.

How to connect the AK7(S) to Fleet Scanner

  1. Get a Mini SIM (2FF size) with mobile data that works on 3G or 2G where you drive, and put it in the AK7S.
  2. Plug in the 6 pin Molex harness. Run its wires to power (a 12 V or 24 V system), to ground and to the ignition line. Fix the box with screws or tape, and place the GPS antenna on its SMA socket where it can see the sky.
  3. Open the settings with ATrack’s ACT tool over the RS232 cable, through the ATrack Device Management portal (ADM), or by SMS. Set the APN (your SIM’s internet settings), your Fleet Scanner server address with port 21655, TCP or UDP, and how often it should report.
  4. In Fleet Scanner, create the device using its unique ID. Turn the key and go for a short drive, then look at the position, the ignition state and any driver tag on the vehicle page.

ATrack AK7S FAQ

Does Fleet Scanner support the ATrack AK7S?

Yes. Set the AK7S to send to your Fleet Scanner server on port 21655. You then get its live position, ignition, inputs, driver ID and events in one place. Fleet Scanner runs on your own server, and white label is included.

Is the ATrack AK7S still on ATrack’s website?

No. ATrack no longer lists the AK7S on its site. Its English product page now sends you to the home page with a “Not found” message. ATrack still hosts the AK7S datasheet (rev. 20190111), and that is where the specs on this page come from. We did not find a successor named by ATrack.

Where can I find the AK7S SMS commands or manual?

The datasheet says you can set up the AK7S by SMS, through ADM or with an RS232 cable and the ACT tool. ATrack does not publish the full command list on its public pages, so we do not list commands here. Ask the company that sold you the tracker for the AK7S command guide.

Does the AK7S work on 4G?

No. The AK7S-UG uses 3G (UMTS/HSPA) and 2G GSM bands only. Where both 3G and 2G have been switched off, it cannot connect. For those places, pick a 4G tracker; Fleet Scanner works with more than 1,000 GPS devices.

How long does the AK7S backup battery last?

ATrack does not give a time in hours. It says the backup battery is an option, 3.7 V and 650 mAh. While running, the AK7S draws 70 mA at 12 V, and only 4 mA in deep sleep.

Can the AK7S read OBD or truck data?

Only with an add-on. ATrack lists the AC1P and AC1R OBDII_J1939 diagnostic adapters as accessories for it. The datasheet does not list which values they read, so check with your seller before you plan reports around them.

AK7S on the road. Every report on your own server.

From a single tracker to a mixed fleet across 1,000+ device models: live tracking, alerts, fuel, drivers, maintenance and reports in one self-hosted platform. See it with your own hardware.

Get a free demo

More supported GPS trackers

Specs and accessories follow ATrack’s AK7S datasheet (rev. 20190111). Driver ID, temperature, relay, OBD and camera features need ATrack’s optional accessories. ATrack and AK7S are trademarks of ATrack Technology Inc.

Take Control with
Fleet Tracking

Track vehicles in real time, optimize routes, and take full control of your fleet operations.

Free Demo