Skip to content
Fleet Scanner
Hardware integration · ATrack AS11

ATrack AS11 LTE asset tracker, working inside Fleet Scanner

The ATrack AS11 is a 4G LTE asset tracker from ATrack Technology in Taiwan. It has a 6,400 mAh rechargeable battery inside a sealed IP68 case. ATrack builds it for trailers, cold chain trailers, generators and other things that move without a driver. Unlike many battery trackers, it also has wired inputs and outputs for extra parts. Fleet Scanner reads its positions, battery and input states, so each asset sits on your live map next to your vans and trucks.

6,400 mAh rechargeable Li-ionLTE Cat.1 / Cat.M by versionIP68 water and dust sealedPort 21655
ATrack AS11 black rectangular asset tracker with a round 8-pin connector cable
2 monthsbattery life at one report an hour
99GNSS channels (GPS and GLONASS)
2.5 mlocation accuracy (CEP 50%)
2 + 2digital inputs and outputs, plus ignition
250 gweight of the tracker
gps · glonass · sbas
GNSS GPS + GLONASSFix 2.5 m
01 · Live tracking · 99 channel engine

Trailer positions from GPS and GLONASS

The AS11 listens to GPS and GLONASS satellites with a 99 channel engine. It also uses SBAS correction signals such as WAAS and EGNOS, and ATrack rates its accuracy at 2.5 m. The antenna sits inside the case, and some versions take an outside antenna on an SMA plug. Each report becomes a dot on the Fleet Scanner map, and the dots join into a route you can replay to see where a trailer went last week.

Position Speed and heading Satellites in use External GPS antenna (option)
Trailer and container tracking →
li-ion · 6,400 mAh68%
Report every 1 hBattery 62 %
02 · Battery life · Datasheet

About two months on one charge at hourly reports

Inside the AS11 is a 3.7 V lithium battery of 6,400 mAh. ATrack says it lasts up to 2 months when the tracker reports once an hour. In deep sleep it uses less than 1.2 mA. More reports mean a shorter run, so pick the gap that fits the asset. Fleet Scanner shows the battery level for each unit and can warn you when it gets low.

Battery level Report interval Deep sleep
Fleet reports and dashboards →
main power · 12 / 24 V12.6V
Main 24 VIgnition off
03 · Vehicle power · 8-pin connector

Wire it to 12 V or 24 V when the asset has power

The AS11 does not have to live on its battery alone. Through its round 8-pin connector it can run on a 12 V or 24 V vehicle system. ATrack gives a working draw of 30 to 120 mA at 12 V. On a powered trailer or a truck it runs from the supply, and without it, from the battery. Fleet Scanner reads the power state with each report.

Main power Ignition input Battery or wired mode
Fleet asset management software →
din · dout · ain · rs232DIN1 Ignition ONAIN1 12.4 VDOUT1 Relay OFF
Input 1 ONAnalog 12.6 V
04 · Inputs and outputs · GPIO

Inputs, outputs and RS232 for extra parts

This is where the AS11 stands apart from most battery trackers. It has one ignition input, up to two digital inputs, up to two digital outputs that can sink 500 mA, and one analog input from 0 to 40 V. There is also an RS232 port. ATrack sells parts for it, such as an SOS button cable, a 12 V or 24 V relay and RS232 adapters. Fleet Scanner shows each input change in the asset history.

Digital inputs (up to 2) Digital outputs (up to 2) Analog input 0 to 40 V RS232
Real-time fleet alerts →
accelerometer · ±16 gsleepmoving
State MOVINGYard left
05 · Movement · 3-axis sensor

A motion sensor that notices when the asset moves

A built-in 3-axis accelerometer (motion sensor) with a ±16 g range lets the AS11 tell when it is moving. ATrack lists it for motion detection. That helps with a generator or trailer that should stay put in a yard. ATrack’s own FAQ says its trackers send no event reports until you set them up, so you choose which events it sends. Fleet Scanner logs every start and stop it reports.

Motion start Motion stop Event reports (set by you)
Fleet geofencing software →
1-wire · temp · id
Temp 3.8 °CTrailer T-112
06 · 1-Wire sensors · Optional accessory

Temperature probes and iButton tags on 1-Wire

The AS11 has a 1-Wire port. With ATrack’s add-on parts it can read a 1-Wire temperature probe, an iButton reader and tag, or a 1-Wire trailer ID. ATrack names cold chain trailers as a main use. Fleet Scanner puts the temperature next to each position and can alert you when a load gets too warm. A trailer ID helps you see which trailer is behind which truck.

1-Wire temperature iButton ID Trailer ID
Cold chain tracking →
bluetooth le · class 2
BLE onTyre ok
07 · Bluetooth · Some versions

Bluetooth Low Energy for tyre and other sensors

Some AS11 versions come with Bluetooth Low Energy, Class 2, with long range support. ATrack lists its own Bluetooth tyre pressure (TPMS) sensors, inside and outside types, and a TPMS repeater as parts that go with the AS11. Check the order code when you buy, because there is also a version without Bluetooth. Fleet Scanner shows the sensor values with the asset.

BLE sensor data Tyre pressure (TPMS)
Preventive maintenance scheduling →

AS11 specifications

NetworkAS11-MX (North America): LTE FDD Cat.M B2/B4/B12/B13. AS11-LK (Japan, EMEA): LTE FDD Cat.1 B1/B3/B5/B8/B9/B18/B19/B26/B28, WCDMA 800/850/900/2100. AS11-LG (Global): LTE FDD Cat.1 B1/B2/B3/B4/B5/B7/B8/B9/B12/B13/B14/B18/B19/B20/B25/B26/B28. AS11-LX (North America, Canada): LTE FDD Cat.1 B2/B4/B5/B12/B13
Positioning99 channel engine, GPS and GLONASS, SBAS (WAAS, EGNOS, GAGAN, MSAS); 2.5 m CEP 50%; -167 dBm tracking, -149 dBm acquisition sensitivity; internal antenna, external SMA antenna as an option
DataUDP/IP, TCP/IP, SMS over IMS
Battery3.7 V Li-ion, 6,400 mAh, up to 2 months at an hourly report
PowerVehicle 12 V / 24 V system; 30 to 120 mA at 12 V working, under 1.2 mA at 12 V in deep sleep
Inputs and outputs1 positive ignition input, up to 2 digital inputs, up to 2 digital outputs (500 mA sink), up to 1 analog input (0 to 40 V, 12 bit), RS232, 1-Wire (iButton, temperature, with accessories), vehicle bus through an external adapter
Sensors3-axis accelerometer, ±16 g
Memory64 Mbit internal flash for logs and queued reports
ConnectorsCircular 8-pin I/O connector, nano SIM (4FF), RS232 configuration port
Size / weight120 x 80 x 36 mm, 250 g, flame retardant ABS + PC, IP68
Environment-20 to +60 °C with battery, -40 to +70 °C without; 95% RH at 50 °C non-condensing
MountingScrew mount or magnet mount
Setup toolsADM (ATrack Device Management), firmware and settings over the air (FOTA), RS232 cable
Fleet Scanner port21655 (TCP)

Specifications can differ between hardware revisions. Check the manufacturer’s datasheet for your exact unit.

How to connect the AS11 to Fleet Scanner

  1. Pick the AS11 version that fits your country (MX, LK, LG or LX) and get a nano SIM with data that works on that network. Fit the SIM, then check that the GNSS and cellular lights come on.
  2. Set up the tracker with ATrack’s tools: the ADM (ATrack Device Management) portal, an update over the air, or a PC on the RS232 cable. Enter the APN of your SIM (its internet settings), then the address of your Fleet Scanner server and port 21655. The exact commands are in the ATrack AS11 manual, which ATrack shares with its partners.
  3. Turn on the event reports you want, such as motion and input changes, since ATrack trackers send none by default. In Fleet Scanner, create the unit with the IMEI printed on the AS11 and pick which trailer or asset carries it.
  4. Fix the AS11 to the asset with screws or the magnet kit, with a clear view of the sky. If the asset has power, wire the 8-pin cable to the 12 V or 24 V supply. Take it outdoors and wait for the first position on the map.

ATrack AS11 FAQ

Does Fleet Scanner work with the ATrack AS11?

Yes. The AS11 speaks the ATrack protocol family, and Fleet Scanner takes it on port 21655. Add the tracker by IMEI and you get its positions, battery level, input changes and sensor readings on the map, in alerts and in reports.

How long does the ATrack AS11 battery last?

ATrack rates the 6,400 mAh battery at up to 2 months with one report an hour. Shorter gaps between reports use more power, so the battery runs out sooner. If the asset has 12 V or 24 V power, you can wire the tracker to it.

How do I configure the AS11 and point it at a tracking server?

ATrack sets up its trackers with the ADM portal, over the air updates or an RS232 cable, using the commands in the AS11 manual. Set the APN, then your server address and port. For Fleet Scanner the port is 21655. ATrack’s public site does not list SMS setup commands for the AS11, so use the manual from ATrack or your seller.

Is the ATrack AS11 a 4G tracker?

Yes. The MX version uses LTE Cat.M for North America. The LK, LG and LX versions use LTE Cat.1, and the LK version also has WCDMA (3G). Choose the version made for your region and check that your SIM works on that network.

Is the AS11 still sold?

Yes. ATrack still lists the AS11 on its website as an LTE asset tracker, and it put out an updated datasheet in October 2026.

AS11 on the trailer. Battery, inputs and sensors on one map.

From a single tracker to a mixed fleet across 1,000+ device models: live tracking, alerts, fuel, drivers, maintenance and reports in one self-hosted platform. See it with your own hardware.

Get a free demo

More supported GPS trackers

Specifications from the ATrack AS11 product page, the AS11 datasheet (October 2026) and the AS11 product sheet (rev. 20191219). Traccar’s public device list places the AS11 in the ATrack protocol family. Battery life is ATrack’s rating at an hourly report and changes with settings and signal. ATrack and AS11 are trademarks of ATrack Technology Inc.

Take Control with
Fleet Tracking

Track vehicles in real time, optimize routes, and take full control of your fleet operations.

Free Demo