Skip to content
Fleet Scanner
Hardware integration · Concox BL10

Concox BL10 GPS bike lock, working inside Fleet Scanner

The Concox BL10 GPS bike lock is a lock for shared bikes, made by Jimi IoT. It keeps the bike locked, shows where it is and opens with Bluetooth or a QR code in an app. A solar panel and a 10,000 mAh battery keep it going. Fleet Scanner puts every lock on one map, with alerts when a bike leaves its zone or someone tries to break it.

10,000 mAh battery + solar2G quad-band GSMGPS + LBS positioningPort 10224
Concox BL10 dark grey ring-shaped bike lock with a QR code sticker on top
10,000 mAhrechargeable battery
40 daysstandby when locked, with no sun
6 V / 5 Wsolar panel power
1 to 10 miBeacon position accuracy
IPX5water resistance
location · 0x12
Bike parkedGPS FIXED
01 · Bike location · GPS

See where each shared bike is parked

Riders leave shared bikes all over town. The BL10 uses GPS to find where its bike is and sends that place over the 2G network. Jimi IoT gives a GPS accuracy of under 2.5 meters in open sky. Fleet Scanner shows every bike on a live map. It keeps a history of where each one has been.

0x01 Login0x12 Location packet Latitude / longitude Time
Live vehicle tracking →
bluetooth 4.0 · unlock
Lock OPENLink Bluetooth
02 · Quick unlock · Bluetooth 4.0

Opens with Bluetooth or a QR code

Each lock has a QR code sticker on top. A rider scans it in the bike app, or the phone talks to the lock over Bluetooth 4.0, and the lock opens. Fleet Scanner keeps the lock’s position and alerts in one place, so your team can see which bikes are out and where.

Bluetooth 4.0 QR code scan App unlock
lbs + ibeacon · positioning
LBS approx.iBeacon 1 to 10 m
03 · Backup location · LBS + iBeacon

Still found under trees and tall buildings

Bikes are often parked where GPS is weak, like a covered rack or a narrow street. The BL10 can then report the mobile towers near it. This is called LBS. Near Bluetooth beacons it can use iBeacon too, which Jimi IoT puts at 1 to 10 meters. Fleet Scanner places the bike in the right area until a GPS fix comes back.

MCC MNC LAC Cell ID iBeacon
geofence · boundary
Zone CampusLeft
04 · Geofences · Virtual zone

An alert when a bike leaves its service area

A geofence is a zone you draw on the map, like a city center, a campus or a park. Jimi IoT says the operator is told when the bike crosses the edge of the zone. In Fleet Scanner you can draw as many zones as you need. You also pick who gets the alert.

Zone in Zone out
Fleet geofencing software →
alarm · 0x16sleepmoving
VibrationBike locked
05 · Vibration alert · 3-axis accelerometer

A warning when someone drills or hammers the lock

A 3-axis accelerometer inside the BL10 feels shaking. When the shaking goes past a set level, it sends a vibration alert. Jimi IoT names drilling, hammering and bike theft as the cases it is made for. Fleet Scanner shows the alert with the time and place, so someone can go and check the bike.

0x16 Alarm packet Vibration alert 3-axis accelerometer
Fleet alerts management software →
power · solar68%
Solar chargingStandby 40 days
06 · Solar charging · 6 V / 5 W panel

Sunlight tops up the battery

The BL10 has a 6 V, 5 W solar panel that turns sunlight into power. It charges a 10,000 mAh battery. Even with no sun at all, Jimi IoT says it can stay on standby for up to 40 days while locked. That means fewer trips to charge locks by hand.

Solar panel 6 V / 5 W Battery 10,000 mAh Regular upload mode
Fleet asset management software →
status · 0x1312.6V
Battery lowGSM online
07 · Low battery · Status packet

Know which locks need power first

When the battery runs low, the BL10 sends a low battery alert. One blue light on the lock shows its status. Fleet Scanner lists the battery state of every lock in your fleet. So your team can see which bikes to check before they stop reporting.

0x13 Status / heartbeat Low battery alert Blue status light
Fleet reports and dashboards →
body · ipx5
Rating IPX5Case sealed
08 · Tough build · Rugged case

Hard to break, fine in the rain

Jimi IoT says the case and the way it is fixed make the BL10 hard to damage without special tools. It is rated IPX5, so rain and splashes do not stop it. It works from -20 to +60 °C. Jimi IoT also lists audible recovery as one of its uses.

IPX5 -20 to +60 °C Audible recovery

BL10 specifications

Network2G GSM quad-band 850/900/1800/1900 MHz
PositioningGPS + LBS; < 2.5 m CEP; -165 dBm tracking, -148 dBm acquisition sensitivity; iBeacon 1 to 10 m
Time to first fixHot start 1 s or less, cold start 32 s or less on average (open sky)
Battery10,000 mAh / 3.7 V industrial-grade Li-Polymer
Solar6 V / 5 W (in sunlight)
Working mode / standbyRegular upload mode; up to 40 days standby when locked, without solar power
InterfacesMicro-SIM, 1 blue status light, Bluetooth 4.0, 64 Mb storage
Sensors3-axis accelerometer
Size / weight148.0 x 211.0 x 51.0 mm, 1,117 g
EnvironmentIPX5, -20 to +60 °C, 5% to 95% humidity (non-condensing)
Fleet Scanner port10224 (TCP)

Specifications can differ between hardware revisions. Check the manufacturer’s datasheet for your exact unit.

How to connect the BL10 to Fleet Scanner

  1. Put a Micro-SIM card into the BL10. It needs a plan that works on the 2G (GSM) network and has data (GPRS) and SMS.
  2. Set the APN (your SIM’s internet settings) and your Fleet Scanner server’s domain or IP with port 10224. Jimi IoT’s leaflet does not print the commands, so use the BL10 command list from Jimi IoT.
  3. In Fleet Scanner, add the lock by the IMEI number on its label. Link it to the bike it is fitted to, and draw your service area as a geofence.
  4. Fit the lock on the bike, in a spot where the sun can reach it, so the solar panel can charge the battery. Then check that the bike’s first position shows on the map.

Concox BL10 FAQ

Can the Concox BL10 bike lock work with Fleet Scanner?

Yes. Set the BL10 to send to your own Fleet Scanner server on port 10224. Fleet Scanner then shows each bike on the map and passes on its vibration, low battery and geofence alerts.

How long does the BL10 battery last?

The battery is 10,000 mAh. Jimi IoT says the lock can stay on standby for up to 40 days while locked, with no solar power at all. In sunlight, its 6 V, 5 W solar panel charges the battery too. Fleet Scanner warns you when a lock runs low.

How do riders unlock a BL10?

Jimi IoT lists two ways. The rider scans the QR code on the lock in a bike app, or the phone opens it over Bluetooth 4.0. The unlock is handled by that app. Fleet Scanner tracks the lock and its alerts.

Is the Concox BL10 still sold, and is it 4G?

Jimi IoT still lists the BL10 under its bike trackers, with no end of life note. It works on 2G (GSM), not 4G, so check that 2G still works in your city. Jimi IoT also lists the JM-BL11, a 4G GPS bike lock.

BL10 on the wheel. Every shared bike on one map.

From a single tracker to a mixed fleet across 1,000+ device models: live tracking, alerts, fuel, drivers, maintenance and reports in one self-hosted platform. See it with your own hardware.

Get a free demo

More supported GPS trackers

Packet types follow the Concox GT06 communication protocol used by Jimi IoT trackers. Battery and standby times are Jimi IoT’s figures and change with settings, sunlight and signal. Concox, Jimi IoT and BL10 are trademarks of Jimi IoT. Specifications from the Jimi IoT BL10 product page and leaflet.

Take Control with
Fleet Tracking

Track vehicles in real time, optimize routes, and take full control of your fleet operations.

Free Demo