Skip to content
Fleet Scanner
Hardware integration · Concox GT06E

Concox GT06E 3G tracker, working inside Fleet Scanner

The Concox GT06E 3G GPS tracker is the 3G member of the GT06 family. It keeps the protocol and the remote cut-off that made the GT06N popular. But it connects over 3G (WCDMA) and falls back to 2G (GSM). Fleet Scanner reads its location, status and alarm packets. It turns them into live tracking, instant alerts and an engine cut-off you can trust.

3G WCDMA + GSMGPS + LBS positioningRelay fuel / power cutPort 10222
Concox GT06E 3G vehicle GPS tracker with wiring harness
3GWCDMA with GSM fallback
7alarm types
GPS + LBSpositioning
Relayremote fuel / power cut-off
GT06protocol family
location · 0x12 / 0x22
Speed 48 km/h3G
01 · Live tracking · GPS + LBS packets

Live position, speed and direction over 3G

Location packets have the date and time and the satellites in use. They also have the latitude, longitude, speed and direction (heading), plus the cell tower in use. Fleet Scanner shows every GT06E vehicle live. It keeps the route so you can play it back.

0x12 GPS + LBS0x22 GPS + LBS (extended)0x01 Login Speed Course
Live vehicle tracking →
alarm · 0x16SOS
Door OPENSOS
02 · Alarms · Alarm packets

SOS, power cut, vibration and door alarms

Some events send an alarm with the position attached. These are an SOS press, the vehicle power being cut and shaking (vibration) while parked. A door opening and a low backup battery send one too. Fleet Scanner sends them to you as instant alerts.

0x01 SOS0x02 Power cut0x03 Vibration0x14 Door0x0F Low battery
Fleet alerts management software →
alarm · geofence / speed
Overspeed
03 · Geofences and speed · Alarm packets

Geofence and overspeed (speeding) alarms

A geofence is a zone you draw on the map. The tracker itself sends geofence and speeding alarms. Fleet Scanner also lets you add as many zones and speed rules as you like on its side. Use them for depots, sites and no-go roads.

0x04 Geofence0x06 Overspeed
Fleet geofencing software →
command · 0x80
Cut-off ARMED
04 · Remote cut-off · Relay output

Remote fuel or power cut-off

First, the relay must be installed. A relay is a switch the tracker can turn on and off. Then an approved user can cut the fuel pump or ignition from Fleet Scanner. They can turn it back on later. The status packet confirms when fuel (oil) and power (electricity) are cut.

0x80 Server command Oil & electricity cut (status bit 7)
Vehicle and equipment protection →
lbs · cell towers
LBS approx.
05 · Cell-tower location · LBS

A rough location when GPS is blocked

The GT06E reports the mobile cell tower it is using. So Fleet Scanner can still place a vehicle in an underground car park or a covered yard. It does this until the tracker sees satellites again.

0x19 LBS status MCC MNC LAC Cell ID
status · 0x1312.6V
ACC ONSupply 12.3 V
06 · Ignition and power · Status packets

Ignition (ACC), external voltage and signal

Status and heartbeat packets are regular check-in messages. They carry the ignition (ACC), charging, cut-off state, battery level and GSM signal. Information packets report the vehicle’s power voltage. Fleet Scanner uses ignition for trips and engine hours. It alerts you when the vehicle battery is weak.

0x13 Status / heartbeat0x94 Info (external voltage) ACC GSM signal
Trip planning and trip records →

GT06E specifications

Network3G WCDMA with GSM fallback (bands depend on the version)
PositioningGPS plus cell-tower (LBS) location
Inputs / outputsIgnition (ACC) and door inputs, SOS button, relay output
AlarmsSOS, power cut, vibration, door, geofence, overspeed, low battery
Remote controlFuel or power cut-off and restore through the relay
ProtocolConcox GT06 (binary, TCP)
Fleet Scanner port10222 (TCP)

Specifications can differ between hardware revisions. Check the manufacturer’s datasheet for your exact unit.

How to connect the GT06E to Fleet Scanner

  1. Fit the GT06E out of sight. Connect power, ground and ACC (ignition). Also connect the door wire if you use it, and the relay for remote cut-off.
  2. Put in a 3G data SIM. Send the SMS command SERVER,0,<your server>,10222,0#. Then send the APN command (your SIM’s internet settings).
  3. In Fleet Scanner, add the tracker by its IMEI number and assign it to a vehicle.
  4. Take a short test drive. Then test the SOS button and the door alarm.

Concox GT06E FAQ

Does Fleet Scanner support the Concox GT06E?

Yes. Fleet Scanner reads the GT06E’s GT06 location, status, alarm and information packets. It also sends the cut-off command. It reports on port 10222.

Is the GT06E 3G or 4G?

The GT06E is a 3G (WCDMA) tracker that falls back to GSM (2G). Some places are closing their 3G networks. There, choose a 4G Jimi IoT model such as the JM-VL02.

What is the difference between the GT06E and the GT06N?

Both use the GT06 protocol and support remote cut-off. The GT06N is a 2G tracker. The GT06E moves the same design to 3G.

Can I cut off the engine with the GT06E?

Yes, when the relay is installed. Fleet Scanner sends the cut-off and restore commands. Only approved users can send them.

GT06E plugged in. Fleet running on one platform.

From a single tracker to a mixed fleet across 1,000+ device models: live tracking, alerts, fuel, drivers, maintenance and reports in one self-hosted platform. See it with your own hardware.

Get a free demo

More supported GPS trackers

Packet types and alarm codes follow the Concox GT06 protocol. Hardware details vary between GT06E batches and sellers. Concox and GT06E are trademarks of Jimi IoT.

Take Control with
Fleet Tracking

Track vehicles in real time, optimize routes, and take full control of your fleet operations.

Free Demo