Skip to content
Fleet Scanner
Hardware integration · Concox WeTrack2

Concox WeTrack2 GPS tracker on your Fleet Scanner server

The Concox WeTrack2 GPS tracker is a small 2G box for e-bikes, e-scooters, motorcycles, cars and trucks. Jimi IoT (Concox) builds it. It runs on any vehicle power from 9 to 90 V, so one model fits a 12 V car and a 72 V scooter. Its data comes in the GT06 protocol, a common set of rules many trackers use to talk to a server. Fleet Scanner understands every WeTrack2 message about place, ignition and alarms. You get live tracking, power and speeding alerts, and a remote fuel or power cut-off.

2G quad-band GSM9-90 V wide voltageRelay fuel / power cutPort 10000
Black Concox WeTrack2 GPS tracker with its short power cable
9-90 Vvehicle power range
270 mAhbackup battery
60 hstandby time
IP65dust and water resistance
3SOS phone numbers
location · 0x12 / 0x22
Speed 32 km/hGPRS ONLINE
01 · Live tracking · GPS + LBS packets

Live position on bikes, scooters and trucks

The WeTrack2 sends its position, speed and heading over 2G GPRS. You pick how often. One timer is for when the ignition is on and one is for when it is off. Each can be 5 to 18,000 seconds, and both start at 20 seconds. Fleet Scanner puts every WeTrack2 on one live map. It saves each route, and you can replay any day on the map.

0x01 Login0x12 GPS + LBS0x22 GPS + LBS (extended) TIMER,T1,T2# Speed
Live vehicle tracking →
alarm · power cut12.6V
Power cutBattery backup
02 · Power alarms · Alarm packets

Wire cut and low battery alarms

If someone cuts the tracker’s power wire, it switches to its own battery and raises an alarm. It texts and calls your SOS numbers, and it sends the alarm to the server. When it is running on its battery alone and the battery drops below 3.7 V, it sends a low battery alarm. Fleet Scanner turns both into instant alerts, so a cut wire never goes unseen.

0x16 Alarm packet0x02 Power cut0x0F Low battery SOS,A,No.1,No.2,No.3#
Fleet alerts management software →
alarm · 0x03sleepmoving
Armed YESVibration
03 · Vibration alarm · Accelerometer

A shake alarm for parked vehicles

A motion sensor (accelerometer) inside the WeTrack2 feels the vehicle move. The vibration alarm is off when it leaves the factory. Once you turn it on, the tracker arms itself a set time after the ignition goes off. If the parked vehicle then shakes several times, it sends a vibration alarm. Fleet Scanner shows the alarm with the position, so you can check on the vehicle fast.

0x03 Vibration SENALM,ON# DEFENSE,TIME#
Fleet alerts management software →
alarm · fence / speed
Limit 50 km/hOverspeed
04 · Geofences and speed · Alarm packets

Geofence and speeding alerts

Think of a geofence as a fence you draw around a place on the map. The WeTrack2 can tell you when a vehicle goes into or out of a zone. It also warns you when the average speed stays above your limit for a time you choose. The limit can be 1 to 255 km/h. Fleet Scanner adds its own zones and speed rules on top, with no limit, and each one sends its own alert.

0x04 Fence in0x05 Fence out0x06 Overspeed SPEED,ON,Time,Limit,Way#
Fleet geofencing software →
command · 0x80
Cut-off ARMEDSpeed 0 km/h
05 · Remote cut-off · Relay output

Cut the fuel or power from far away

A relay and relay socket come in the box. The relay works like a light switch that the tracker flips. The yellow wire goes to pin 86 of the relay. After that, an approved user can stop the fuel pump or the electric supply from Fleet Scanner, then let it run again later. For safety, the WeTrack2 waits for a GPS fix and a speed under 20 km/h, or a stopped vehicle, before it acts.

0x80 Server command RELAY,1# / RELAY,0# CENTER,A,number#
Vehicle and equipment protection →
status · 0x13DIN1 Ignition ONAIN1 12.4 VDOUT1 Relay OFF
ACC OFFGSM 3/5
06 · Ignition and status · Status packets

Ignition (ACC) state for trips

The orange wire goes to the ignition (ACC) switch. Every so often the tracker sends a status or heartbeat packet, a quick hello. It tells the server if the ignition is on or off, and it carries the GSM signal and battery level. Fleet Scanner uses the ignition to split the day into trips and to count engine hours. Signal and battery appear on the tracker’s health card.

0x13 Status / heartbeat ACC GSM signal Battery level
Trip planning and trip records →

WeTrack2 specifications

Network2G GSM quad-band 850/900/1800/1900 MHz, GPRS
PositioningGPS plus cell-tower (LBS) location
Power supply9 to 90 V DC (the manual says to wire it to a vehicle battery of no more than 72 V)
Backup battery270 mAh 3.7 V Li-Polymer, about 60 hours standby
Wiring4 wires: power (red), ground (black), ACC (orange), relay control (yellow)
InterfacesStandard SIM card, blue GNSS, green cellular and red power LEDs, 32+32 Mb memory
SensorsAccelerometer for the vibration alarm
Size / rating78 x 41 x 13 mm, IP65, -20 to +70 °C operating range
ProtocolConcox GT06 (binary, TCP)
Fleet Scanner port10000 (TCP)

Specifications can differ between hardware revisions. Check the manufacturer’s datasheet for your exact unit.

How to connect the WeTrack2 to Fleet Scanner

  1. Find a hidden spot with the "this side towards sky" face up, for example under the dashboard or under a motorcycle seat. Keep metal off the top. Connect red to the battery plus (with the 1 A fuse), black to ground and orange to the ignition (ACC). Want remote cut-off? Put the relay in the fuel pump or power line.
  2. Open the cover, put in a 2G SIM with data and SMS, and turn the battery switch on. Send APN,your APN name# to set your SIM’s internet settings. Then send SERVER,0,your server IP,10000,0# (or SERVER,1,your domain,10000,0#). The tracker replies OK.
  3. Set the report timer with TIMER,T1,T2# if you want a rate other than 20 seconds. Add your SOS numbers with SOS,A,number# and the cut-off phone with CENTER,A,number#. Send PARAM# or GPRSSET# to check the settings.
  4. Open Fleet Scanner, type in the tracker’s IMEI number and link it to a vehicle. Take a short ride and check the position and ignition on the live map.

Concox WeTrack2 FAQ

Does Fleet Scanner work with the Concox WeTrack2?

Yes. The WeTrack2 talks in the GT06 protocol, and Fleet Scanner reads its location, status, heartbeat and alarm packets. Fleet Scanner can also send it the relay commands. Set your Fleet Scanner server and port 10000 on the tracker by SMS.

How do I connect the WeTrack2 to my own tracking server?

It comes set to the maker’s own platform, so you change it by text message. Send APN,your APN# first. Then send SERVER,0,IP,10000,0# for an IP address, or SERVER,1,domain,10000,0# for a domain name. Send RESET# if it still does not show up online.

How long does the WeTrack2 battery last?

The 270 mAh battery is a backup for when vehicle power is cut. Jimi IoT’s manual gives about 60 hours of standby. When the battery falls below 3.7 V, the tracker texts your SOS numbers and tells the server, so you know to recharge or fix the power.

Can I stop a vehicle with the WeTrack2?

Yes, once the relay is wired. From Fleet Scanner, approved users send the cut-off and restore commands. By SMS, only the center number can send RELAY,1# to cut and RELAY,0# to restore. The cut only happens with a GPS fix and below 20 km/h.

WeTrack2 wired in. Bikes, scooters and trucks on one map.

From a single tracker to a mixed fleet across 1,000+ device models: live tracking, alerts, fuel, drivers, maintenance and reports in one self-hosted platform. See it with your own hardware.

Get a free demo

More supported GPS trackers

Packet and alarm codes are from the Concox GT06 protocol. SMS commands are from the WeTrack2 user manual v1.2. Concox, Jimi IoT and WeTrack2 are trademarks of Jimi IoT. Specifications from the Jimi IoT WeTrack2 product page, leaflet and user manual.

Take Control with
Fleet Tracking

Track vehicles in real time, optimize routes, and take full control of your fleet operations.

Free Demo