Skip to content
Fleet Scanner
Hardware integration · Jimi IoT JM-LG01

Jimi IoT JM-LG01 GPS tracker for assets, working inside Fleet Scanner

The Jimi IoT JM-LG01 GPS tracker is a small, wireless tracker for things that have no power of their own. Think rental cars, financed cars, trailers and goods. It is made by Jimi IoT (Concox). It weighs only 72 g and holds on to metal with a magnet. A 2,800 mAh battery inside keeps it going, so you fit no wires at all. It sends data over 2G mobile networks and finds its place with GPS and cell towers. Fleet Scanner reads its positions and tamper alarms and puts each asset on your map.

2,800 mAh disposable battery2G GSM quad-bandGPS + LBS positioningPort 10013
Illustration of the Jimi IoT JM-LG01 GPS tracker
2,800 mAhbuilt-in battery
1.5 yearsstandby in power-saving mode
72 gtotal weight
IPX5water resistance
4GSM bands supported
location · tracking mode
Mode TRACKINGGSM
01 · Tracking mode · GPS + LBS

Regular position reports while the asset is on the move

In tracking mode, the JM-LG01 checks its position and sends it on a timer you set by SMS. Shorter gaps give you a finer route. Longer gaps save battery. Fleet Scanner draws each report on the live map. It saves every point, so you can play back where a car or trailer went last week.

0x01 Login Location packet0x13 Status / heartbeat Upload interval
Live vehicle tracking →
standby · power-saving68%
Mode SLEEPLast check-in 06:00
02 · Long standby · Power-saving mode

Up to 1.5 years on one battery

The JM-LG01 runs on a 2,800 mAh lithium-manganese battery. This battery is not made to be charged. In power-saving mode, the tracker sleeps between reports and only wakes to send its place. Jimi IoT rates this at up to 1.5 years of standby. Fewer reports mean a longer life. Fleet Scanner shows the last check-in time for every tracker, so you spot a quiet one fast.

Power-saving mode Wake and report Battery switch
Fleet asset management software →
lbs · cell towers
GPS no fixLBS area
03 · No sky view · LBS

A rough place from cell towers when GPS is blocked

A car in a basement garage or a box in a steel trailer cannot see the satellites. Then the JM-LG01 sends the cell towers it can hear instead. This is called LBS, short for location based service. Fleet Scanner turns those towers into an area on the map. As soon as a GPS fix comes back, the exact point takes over.

MCC MNC LAC Cell ID
alarm · light sensorX -612Y 180Z 990
TamperLight detected
04 · Tamper alert · Light sensor

An alarm when someone takes the tracker off

The JM-LG01 sits hidden in the dark. It has a light sensor on board. If a thief finds it and pulls it out, light hits the sensor and the tracker sends a tamper alarm. Fleet Scanner pushes that alarm to you right away, with the last known place attached. That gives you a head start while the asset is still close by.

Alarm packet Tamper (light sensor)
Fleet alerts management software →
geofence · server side
Zone City areaOutside
05 · Zones · Fleet Scanner

Get told when a rental car leaves its area

Jimi IoT built the JM-LG01 for car rental, car loans and asset control. In all of these, you want to know when something goes where it should not. In Fleet Scanner, you draw zones on the map around a city, a branch or a parking lot. When a JM-LG01 reports from outside its zone, you get an alert.

Zone in / out Last position
Fleet geofencing software →
install · no wiring12.6V
Wiring noneIPX5
06 · Hidden install · Magnet + IPX5

Small enough to hide, tough enough for outside

The JM-LG01 measures 82 x 42 x 20 mm. It needs no power cable, so you can put it almost anywhere. The magnet on its back sticks to metal in seconds. The case is rated IPX5, so rain and splashes are fine. It works from -20 to +70 °C. Fleet Scanner keeps a note of which asset each tracker sits on.

Magnet mount IPX5 case No power cable
Fleet reports and dashboards →

JM-LG01 specifications

Network2G GSM quad-band 850/900/1800/1900 MHz
PositioningGPS + LBS; -165 dBm tracking, -148 dBm acquisition sensitivity; under 2.5 m CEP
Time to first fixHot start about 1 s, cold start about 32 s (open sky)
Battery2,800 mAh / 3.0 V industrial-grade lithium-manganese, disposable (not rechargeable)
StandbyUp to 1.5 years in power-saving mode
Working modesTracking and power-saving, set by SMS
SIMMicro-SIM with GPRS data and SMS
SensorsLight sensor for tamper alerts
Size / weight82 x 42 x 20 mm, 72 g, IPX5
Environment-20 to +70 °C, 5 to 95 % humidity (no condensation)
ProtocolGT06 family (Jimi IoT), over TCP
Fleet Scanner port10013 (TCP)

Specifications can differ between hardware revisions. Check the manufacturer’s datasheet for your exact unit.

How to connect the JM-LG01 to Fleet Scanner

  1. Get a Micro-SIM that has GPRS data and SMS turned on, and that works on a 2G network where you are. Put it in the JM-LG01 and set the battery switch to ON.
  2. Send the setup SMS commands from the Jimi IoT user manual to the tracker’s number. Set the APN (your SIM’s internet settings) and point it at your Fleet Scanner server’s domain or IP with port 10013. Then pick tracking mode or power-saving mode.
  3. In Fleet Scanner, add the tracker by its IMEI number. Link it to the car, trailer or item it will sit on.
  4. Hide the JM-LG01 in a dark spot and stick it to metal with its magnet. Try not to bury it deep under thick metal, so it can still reach the satellites and the mobile network. Wait for the first report on the map before you leave it.

Jimi IoT JM-LG01 FAQ

Does Fleet Scanner work with the Jimi IoT JM-LG01?

Yes. The JM-LG01 sends GT06 family packets to Fleet Scanner on port 10013. Fleet Scanner reads its GPS and cell tower positions, its heartbeats and its tamper alarm. You see each asset on the map and in reports.

Can I charge the JM-LG01 battery?

No. Jimi IoT lists a 2,800 mAh disposable battery, so it is not made for charging. It is rated for up to 1.5 years of standby in power-saving mode. Sending reports more often makes it run down sooner.

Is the JM-LG01 a 4G tracker?

No. It is a 2G GSM tracker on the 850, 900, 1800 and 1900 MHz bands. Some countries are switching 2G off. Ask your mobile network if 2G will keep running where you plan to use it.

How do I connect the JM-LG01 to a tracking server?

You set it up by SMS. Text the tracker its APN and the server address and port, using the commands in the Jimi IoT manual. For Fleet Scanner, the port is 10013. The SIM must allow both GPRS data and SMS.

Is the JM-LG01 still sold?

Jimi IoT’s current asset tracker range no longer shows the JM-LG01. It now lists 4G models such as the JM-LL01, LL301, LL303 and LL701. Jimi IoT does not name one of them as the direct replacement. Trackers you already own still work with Fleet Scanner.

JM-LG01 hidden away. Every asset still on your map.

From a single tracker to a mixed fleet across 1,000+ device models: live tracking, alerts, fuel, drivers, maintenance and reports in one self-hosted platform. See it with your own hardware.

Get a free demo

More supported GPS trackers

Packet types follow the GT06-family protocol used by Jimi IoT trackers. Battery life is Jimi IoT’s rating and changes with settings and signal. Jimi IoT, Concox and JM-LG01 are trademarks of Jimi IoT. Specifications from the Jimi IoT and Concox JM-LG01 product pages, FAQ and user manual notes.

Take Control with
Fleet Tracking

Track vehicles in real time, optimize routes, and take full control of your fleet operations.

Free Demo