Skip to content
Fleet Scanner
Hardware integration · Jimi IoT JM-VG01U

Jimi IoT JM-VG01U GPS tracker, working inside Fleet Scanner

The Jimi IoT JM-VG01U is a 2G GPS tracker for cars, vans and trucks. It is made by Jimi IoT (Concox). It has a motion sensor and a gyroscope inside. With them it can guess where the vehicle is when GPS is weak, like in a tunnel. This is called INS (inertial navigation). It also spots 8 kinds of bad driving. It uses the GT06 family protocol (the language it uses to send data). Fleet Scanner reads its location, status and alarm packets. It turns them into live tracking, driving alerts and a remote cut-off.

2G GSM networkGPS + INS tunnel trackingRelay fuel / power cutPort 10224
Illustration of the Jimi IoT JM-VG01U GPS tracker
8driving behaviour alerts
9-36 Vsupply range
450 mAhbackup battery
IP65water and dust resistance
< 2%mileage error
location · 0x22
Speed 48 km/hINS ON
01 · Live tracking with INS · GPS + LBS packet

Live tracking that keeps going in tunnels

The JM-VG01U finds its position with GPS and the nearby cell towers. When GPS is weak, like in a tunnel, an underpass or a city centre, its motion sensors keep working out where the vehicle is. It sends position, speed and direction (heading) over 2G. By default it reports every 10 seconds. Fleet Scanner shows every vehicle live. It keeps the full route so you can play it back.

0x22 GPS + LBS location0x01 Login Speed Course Cell ID
Live vehicle tracking →
alarm · driving behaviourX -612Y 180Z 990
Lane changeScore -3 pts
02 · Driving behaviour · Alarm packets

8 driving behaviour alerts, from harsh braking to rollover

A 3-axis motion sensor (accelerometer) and a 3-axis gyroscope watch how the vehicle moves. The tracker reports harsh acceleration, harsh braking, sharp turns and sudden lane changes. It also reports crashes, skidding, rollovers and a vehicle tilted at a strange angle. Small bumps and scratches do not set off the crash alert. Fleet Scanner turns these events into a simple score for each driver, and sends safety alerts to the right person.

0x26 Harsh acceleration0x1A Harsh braking0x1B Sharp cornering0x2C Collision Lane change Skidding Rollover
Driver scorecards →
alarm · 0x16SOS
SOSPosition attached
03 · Security alarms · Alarm packets

SOS button, power cut, vibration and speeding alarms

A panic (SOS) button comes in the box. The driver holds it for 3 seconds to send an alarm. The tracker texts up to 3 phone numbers and calls them in turn. It also sends the alarm to the server. The JM-VG01U warns you when its power is cut, when the vehicle shakes or moves when it should not, and when the driver goes over a speed you choose. Fleet Scanner sends each alarm to you as an instant alert.

0x16 Alarm packet0x01 SOS0x02 Power cut0x03 Vibration0x06 Overspeed Vehicle movement
Fleet alerts management software →
geofence · in / out
Zone DepotFence in
04 · Geofences · Alarm packets

Geofence in and out alarms

A geofence is a zone you draw on the map. Jimi IoT lists geofence alerts for the JM-VG01U. Fleet Scanner also lets you add as many zones as you like on its side. Put them around depots, customer sites and no-go areas. Each zone can have its own alert rules.

0x04 Fence in0x05 Fence out
Fleet geofencing software →
command · relay
Cut-off ARMEDSpeed < 20 km/h
05 · Remote cut-off · Relay output

Remote fuel or power cut-off, made safe

A relay comes in the box. A relay is a switch the tracker can turn on and off. Once it is wired in, an approved user can cut the fuel pump or the power from Fleet Scanner. With the ignition off, the cut-off happens right away. With the ignition on, it waits until the vehicle has a GPS fix and is going slower than 20 km/h. So the vehicle is never cut off while it is going fast.

0x80 Server command RELAY,1# / RELAY,0# Cut-off state
Vehicle and equipment protection →
status · 0x1312.6V
ACC ONTrip 42.6 km
06 · Ignition and mileage · Status packets

Ignition (ACC), trips and mileage you can trust

The orange wire tells the tracker when the ignition (ACC) is on. Status and heartbeat packets are regular check-in messages that carry this state. Jimi IoT says the JM-VG01U’s mileage error can be less than 2%. Fleet Scanner uses ignition and distance for trips, engine hours and service reminders.

0x13 Status / heartbeat ACC Mileage TIMER,T1,T2#
Trip planning and trip records →

JM-VG01U specifications

NetworkGSM (2G) with GPRS data
GNSSGPS with INS (inertial navigation) for weak signal areas, L1, hot start 1 s or less, cold start 32 s or less
Power supply9 to 36 V DC, 38 mA at 12 V
Backup battery450 mAh 3.7 V Li-Polymer, 28 hours standby or 1.5 hours working
Inputs / outputsACC (ignition) and SOS inputs, relay output
InterfacesMicro-SIM, 3 LEDs (GNSS, cellular, power), 32+32 Mb data storage
Sensors3-axis accelerometer and 3-axis gyroscope
Size / weight80 x 67 x 16 mm, 63 g, IP65, works from -20 to +70 °C
ProtocolGT06 family (Jimi IoT)
Fleet Scanner port10224 (TCP)

Specifications can differ between hardware revisions. Check the manufacturer’s datasheet for your exact unit.

How to connect the JM-VG01U to Fleet Scanner

  1. Fit the JM-VG01U out of sight with the "This side towards sky" label facing up, for example under the windshield or around the dashboard. Connect power (red), ground (black) and ACC (orange). Wire the SOS button where the driver can reach it, and the relay if you want remote cut-off. The standard relay is for 12 V. Use a 24 V relay on 24 V vehicles.
  2. Put in a Micro-SIM with SMS and data, then switch the battery switch to ON. Send the SMS commands to set the APN (your SIM’s internet settings). Also set your Fleet Scanner server’s domain or IP with port 10224.
  3. In Fleet Scanner, add the tracker by its IMEI number and assign it to a vehicle.
  4. Take a short test drive. Check the position, ignition and alerts on the live map. Then test the SOS button.

Jimi IoT JM-VG01U FAQ

Does Fleet Scanner support the Jimi IoT JM-VG01U?

Yes. Fleet Scanner reads the JM-VG01U’s GT06 family location, status and alarm packets. These include harsh driving, collision, SOS, power cut and geofence alarms. Fleet Scanner also sends the relay commands. It reports on port 10224.

Is the JM-VG01U 4G?

No. Jimi IoT lists it as a GSM tracker, which means it uses 2G. Before you buy, check that 2G is still running in your country. If you need 4G, look at the Jimi IoT JM-VL01 or JM-VL02.

What does INS-aided GPS mean?

INS means inertial navigation. The tracker uses its motion sensor and gyroscope to work out how the vehicle is moving. When GPS drops out, like in a tunnel, an underpass or a city centre, it uses this to keep the position going.

Can I cut off the engine with the JM-VG01U?

Yes, once the relay is wired in. Fleet Scanner sends the cut-off and restore commands, and only approved users can send them. If the ignition is on, the tracker waits until the vehicle is going slower than 20 km/h.

JM-VG01U plugged in. Fleet running on one platform.

From a single tracker to a mixed fleet across 1,000+ device models: live tracking, alerts, fuel, drivers, maintenance and reports in one self-hosted platform. See it with your own hardware.

Get a free demo

More supported GPS trackers

Packet types and alarm codes follow the GT06-family protocol used by Jimi IoT trackers. Jimi IoT, Concox and JM-VG01U are trademarks of Jimi IoT. Specifications from the Jimi IoT JM-VG01U product page, leaflet and quick start manual.

Take Control with
Fleet Tracking

Track vehicles in real time, optimize routes, and take full control of your fleet operations.

Free Demo