Skip to content
Fleet Scanner
Hardware integration · Jimi IoT JM-VL02

Jimi IoT JM-VL02 4G tracker, working inside Fleet Scanner

The Jimi IoT JM-VL02 4G GPS tracker is made by Jimi IoT (Concox). It is a tough vehicle tracker with an IP65 case. It works on LTE Cat-M1 and NB-IoT networks. These are low-power 4G networks made for small devices. Where LTE-M is missing, it falls back to 2G. It uses the GT06 family protocol (the language it uses to send data). Fleet Scanner reads its location, status and alarm packets. It turns them into live tracking, driving alerts and a remote cut-off.

LTE-M / NB + 2G fallbackIP65 rugged caseRelay fuel / power cutPort 10202
Jimi IoT JM-VL02 4G LTE vehicle GPS tracker
LTE-MCat-M1 / NB with GSM fallback
9–36 Vsupply range
300 mAhbackup battery
IP65water and dust resistance
< 2.5 mGNSS accuracy (CEP)
location · 0x22
Speed 52 km/hLTE-M
01 · Live tracking on LTE-M · GPS + LBS packet

Live tracking that keeps working as 2G shuts down

The JM-VL02 reports its position, speed, direction (heading) and the cell tower it is using. It sends them over LTE Cat-M1 or NB-IoT. Where needed, it falls back to GSM (2G). Fleet Scanner shows every vehicle live. It keeps the full route so you can play it back.

0x22 GPS + LBS location0x01 Login Speed Course Cell ID
Live vehicle tracking →
alarm · driving behaviourX -612Y 180Z 990
CollisionScore -5 pts
02 · Driving behaviour · Alarm packets

Harsh acceleration, braking, cornering and collision

The built-in motion sensor (accelerometer) reports harsh acceleration, harsh braking, sharp cornering and collisions. The tracker also sends a speeding (overspeed) alarm. Fleet Scanner turns them into driver scores and safety alerts.

0x26 Harsh acceleration0x1A Harsh braking0x1B Sharp cornering0x2C Collision0x06 Overspeed
Driver scorecards →
alarm · 0x16SOS
Power cutBackup ON
03 · Security alarms · Alarm packets

SOS, power cut, vibration and power-off alarms

Some events come with the position attached. These are an SOS press, the vehicle power being cut and shaking (vibration) while parked. The tracker switching off is one too. Fleet Scanner sends them to you as instant alerts.

0x01 SOS0x02 Power cut0x03 Vibration0x11 Power off0x0E/0x0F Low battery
Fleet alerts management software →
geofence · in / out
Zone DepotFence in
04 · Geofences · Alarm packets

Geofence in and out alarms

A geofence is a zone you draw on the map. The tracker itself sends fence-in and fence-out alarms. Fleet Scanner also lets you add as many zones as you like on its side. Put them around depots, customer sites and no-go areas.

0x04 Fence in0x05 Fence out
Fleet geofencing software →
command · relay
Cut-off ARMED
05 · Remote cut-off · Relay output

Remote fuel or power cut-off

First, the relay must be installed. A relay is a switch the tracker can turn on and off. Then an approved user can cut the fuel pump or ignition from Fleet Scanner. This helps stop a stolen vehicle. They can turn it back on later. The status packet confirms if the cut-off is on.

Relay,1# / Relay,0# Cut-off state (status bit 7)
Vehicle and equipment protection →
status · 0x1312.6V
ACC ONBattery 12.4 V
06 · Ignition, voltage and status · Status packets

Ignition (ACC), vehicle battery and device status

Status and heartbeat packets are regular check-in messages. They carry the ignition (ACC), charging and cut-off state. Information packets report the vehicle battery voltage. Fleet Scanner uses ignition for trips and engine hours. It alerts you when the vehicle battery is low.

0x13 Status / heartbeat0x94 Info (voltage) ACC Charging
Trip planning and trip records →

JM-VL02 specifications

NetworkLTE Cat-M1 / NB-IoT with GSM 850/900/1800/1900 fallback; bands depend on the A (Americas) or E (Europe) version
GNSSL1 GNSS, < 2.5 m CEP, hot start ≤ 1 s
Power supply9 to 36 V DC
Backup battery300 mAh Li-Polymer
Inputs / outputsACC (ignition) and SOS inputs, relay output
SensorsAccelerometer for harsh driving and collision
Size / weight105.5 x 57 x 21.8 mm, 104 g, IP65
CertificationsCE, FCC, PTCRB and US carrier approvals
ProtocolGT06 family (Jimi IoT)
Fleet Scanner port10202 (TCP)

Specifications can differ between hardware revisions. Check the manufacturer’s datasheet for your exact unit.

How to connect the JM-VL02 to Fleet Scanner

  1. Fit the JM-VL02 out of sight. Connect power, ground and ACC (ignition). If you want remote cut-off, wire the relay too.
  2. Put in a SIM with LTE-M or NB-IoT service. Send the SMS commands to set the APN (your SIM’s internet settings). Also set your Fleet Scanner server’s domain or IP with port 10202.
  3. In Fleet Scanner, add the tracker by its IMEI number and assign it to a vehicle.
  4. Take a short test drive. Check the position, ignition and alerts on the live map.

Jimi IoT JM-VL02 FAQ

Does Fleet Scanner support the Jimi IoT JM-VL02?

Yes. Fleet Scanner reads the JM-VL02’s GT06 family location, status and alarm packets. These include harsh driving, collision, SOS, power cut and geofence alarms. Fleet Scanner also sends the relay commands. It reports on port 10202.

Does the JM-VL02 work on 4G?

Yes. It uses LTE Cat-M1 and NB-IoT. These are low-power 4G networks built for small connected (IoT) devices. Where they are not available, it falls back to GSM (2G).

Can I cut off the engine with the JM-VL02?

Yes, when the relay is installed. Fleet Scanner sends the cut-off and restore commands. Only approved users can send them.

Is the JM-VL02 waterproof?

It is rated IP65, so it keeps out dust and jets of water. That makes it a good fit for trucks, construction vehicles and motorbikes.

JM-VL02 plugged in. Fleet running on one platform.

From a single tracker to a mixed fleet across 1,000+ device models: live tracking, alerts, fuel, drivers, maintenance and reports in one self-hosted platform. See it with your own hardware.

Get a free demo

More supported GPS trackers

Packet types and alarm codes follow the GT06-family protocol used by Jimi IoT trackers. Jimi IoT, Concox and JM-VL02 are trademarks of Jimi IoT. Specifications from Jimi IoT product listings.

Take Control with
Fleet Tracking

Track vehicles in real time, optimize routes, and take full control of your fleet operations.

Free Demo