Skip to content
Fleet Scanner
Hardware integration · Jimi IoT JM-LL01

Jimi IoT JM-LL01 asset GPS tracker, working inside Fleet Scanner

The Jimi IoT JM-LL01 is a wireless GPS tracker for trailers, containers, machines and vehicles. It is made by Jimi IoT (Concox). It runs on a big 10,000 mAh battery and sticks to metal with a strong magnet, so there are no wires to fit. It uses LTE Cat M1 and NB-IoT, which are low-power 4G networks, and falls back to 2G. It finds its place with GPS, Wi-Fi and cell towers. Fleet Scanner reads its positions, battery level and alarms. So your assets sit on the same map as your vehicles.

10,000 mAh internal batteryLTE-M + NB-IoT + 2G fallbackGPS + Wi-Fi + LBS positioningPort 10013
Illustration of the Jimi IoT JM-LL01 GPS tracker
10,000 mAhrechargeable battery
3 yearsstandby in power-saving mode
10 sshortest report gap while moving
7built-in alert types
IP65dust and water resistance
location · mode 1
Report every 10 sLTE-M
01 · Tracking mode · Mode 1

Live positions as often as every 10 seconds

In tracking mode, the JM-LL01 stays online and sends its position on a timer. While it moves, you can pick a gap from 10 seconds to 1 hour. While it stands still, you can pick from 3 minutes to 24 hours. Fleet Scanner shows each asset live on the map. It keeps the full route so you can play it back.

0x01 Login Location packet Moving interval Still interval Speed
Live vehicle tracking →
standby · mode 268%
Mode STANDBYNext wake 24 h
02 · Long standby · Mode 2

Wakes up, reports, and sleeps again for years

In power-saving mode, the JM-LL01 sleeps most of the time. It wakes up at a time you choose, sends its position and goes back to sleep. You can set it to wake every 1 to 72 hours. Jimi IoT says this gives up to 3 years on one charge, depending on how often it reports. Fleet Scanner shows when the next check-in is due, so a quiet tracker is not a surprise.

Start time Wake interval (1 to 72 h) Battery level
Fleet asset management software →
wifi + lbs · positioning
Wi-Fi approx.Towers 3
03 · Indoor location · GPS + Wi-Fi + LBS

A location even inside a yard, shed or container

GPS needs a view of the sky. When the JM-LL01 cannot see satellites, it can still use nearby Wi-Fi networks and the mobile towers around it. LBS means location from those cell towers. Fleet Scanner uses them to place the asset in the right area. It switches back to an exact GPS fix as soon as one is ready.

Wi-Fi networks MCC MNC LAC Cell ID
alarm · tamper
TamperLight detected
04 · Tamper alerts · Light sensor

Alerts when the tracker is pulled off or opened

The JM-LL01 has a light sensor. When someone pulls the tracker off, light reaches the sensor and it sends a tamper alert. It also sends an alert when the cover is removed. Fleet Scanner sends you the alert straight away, so you can act while the asset is still close.

Tamper alert Cover removal alert
Fleet alerts management software →
alarm · vibrationsleepmoving
VibrationArmed ON
05 · Vibration and speed · Accelerometer

Vibration alarm and over-speed alerts

The JM-LL01 has a built-in motion sensor (accelerometer). It can send a vibration alert if someone shakes or moves the asset. It can also send an alert when the speed goes over a limit. Fleet Scanner saves both with the asset’s history and alerts the right person.

Vibration alert Over-speed alert
geofence · alert
Zone Yard 1Left zone
06 · Geofences · Alarms

Know when a trailer leaves the yard

A geofence is a zone you draw on the map. The JM-LL01 has its own geofence alert. Fleet Scanner also lets you add as many zones as you like on its side. Put them around yards, depots and customer sites. Each zone can have its own alert rules.

Geofence alert
Fleet geofencing software →
status · 0x1312.6V
Battery 81 %Signal 4/5
07 · Battery and power · Status packet

Battery level, low battery and power-off alerts

The JM-LL01 sends a low battery alert before it runs out. It also sends an alert when it is switched off. You can even block the power button, so nobody can turn it off by hand. Fleet Scanner shows the battery level of every JM-LL01. It warns you in time to charge it, and then you can put it back to work.

0x13 Status / heartbeat Low battery Power off alert Power button lock
Fleet reports and dashboards →
bluetooth · app
Bluetooth connected
08 · Bluetooth setup · Bluetooth

Set it up from your phone over Bluetooth

You can change the JM-LL01’s settings by SMS or with the Jimi IoT Lab phone app over Bluetooth. SMS commands can get blocked by some mobile networks, so the app is handy. It can also work with optional Bluetooth accessories from Jimi IoT. Once it is set up, Fleet Scanner does the rest.

Jimi IoT Lab app SMS commands Bluetooth accessories (optional)

JM-LL01 specifications

NetworkLTE Cat M1 and NB2 (NB-IoT) bands B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B20/B26/B28/B66, with 2G (EGPRS) 850/900/1800/1900 MHz fallback
PositioningGPS (L1) + Wi-Fi + LBS; -165 dBm tracking, -148 dBm acquisition sensitivity
Time to first fixHot start 1 s or less, cold start 40 s or less (open sky)
Battery10,000 mAh / 3.7 V industrial-grade Li-Polymer, rechargeable
Working modesStandby, tracking and power-saving; up to 3 years standby in power-saving mode
InterfacesStandard SIM, 1 red status light, 4 blue battery lights, Bluetooth, 32+32 Mb storage
SensorsAccelerometer, light sensor for tamper alerts
CertificatesPTCRB, AT&T and Verizon
Size / weight109 x 61 x 30.5 mm, 297 g, IP65, -20 to +70 °C
ProtocolGT06 family (Jimi IoT), over TCP
Fleet Scanner port10013 (TCP)

Specifications can differ between hardware revisions. Check the manufacturer’s datasheet for your exact unit.

How to connect the JM-LL01 to Fleet Scanner

  1. Charge the JM-LL01 fully. Open the upper cover, put a data SIM card in the holder and turn the power switch ON. Close the cover and hold the power button to switch it on.
  2. Send the SMS commands, or use the Jimi IoT Lab app over Bluetooth. Set the APN (your SIM’s internet settings) and your Fleet Scanner server’s domain or IP with port 10013. Choose tracking mode or power-saving mode and the report times you need.
  3. In Fleet Scanner, add the tracker by its IMEI number. Assign it to a trailer, container or machine.
  4. Stick the JM-LL01 to a metal part of the asset with its magnet, face up to the sky, or fix it with the eyelets. Keep metal and heated windscreens away from its top. Then check the first positions on the map.

Jimi IoT JM-LL01 FAQ

Does Fleet Scanner support the Jimi IoT JM-LL01?

Yes. Fleet Scanner reads the JM-LL01’s GT06 family location, status and alarm packets. That includes tamper, cover removal, vibration, over-speed, geofence, low battery and power-off alerts. It reports on port 10013.

How long does the JM-LL01 battery last?

The battery is 10,000 mAh. Jimi IoT says it lasts up to 3 years on one charge in power-saving mode. The real time depends on how often it reports. More reports use more battery. Fleet Scanner shows the level and warns you before it runs out.

Is the JM-LL01 4G?

Yes. It uses LTE Cat M1 and NB-IoT. These are 4G networks made for small, low-power devices. Where they are not available, it falls back to 2G. Check that your SIM card and mobile network support LTE-M or NB-IoT.

Does the JM-LL01 need wiring?

No. It runs on its own battery and holds on to metal with a strong magnet. It also has eyelets to screw or strap it in place. You charge it with the cable in the box, then put it back on the asset.

JM-LL01 switched on. Assets on the same map as your fleet.

From a single tracker to a mixed fleet across 1,000+ device models: live tracking, alerts, fuel, drivers, maintenance and reports in one self-hosted platform. See it with your own hardware.

Get a free demo

More supported GPS trackers

Packet types follow the GT06-family protocol used by Jimi IoT trackers. Battery figures are Jimi IoT’s ratings and depend on settings and signal. Jimi IoT, Concox and JM-LL01 are trademarks of Jimi IoT. Specifications from the Jimi IoT JM-LL01 product page, leaflet and user manual v1.1.

Take Control with
Fleet Tracking

Track vehicles in real time, optimize routes, and take full control of your fleet operations.

Free Demo