Skip to content
Fleet Scanner
Hardware integration · SEEWORLD S06A

SEEWORLD S06A GPS tracker, wired in and tracked in Fleet Scanner

The SEEWORLD S06A is a wired 2G GPS tracker that SEEWORLD builds for delivery trucks, rental cars and loan vehicles. It runs on the vehicle’s own power and keeps a small battery for power cuts. A light sensor and a vibration sensor tell you when someone shakes it or pulls it out, and a relay lets you cut the fuel from far away. Fleet Scanner takes every report on your own server and turns it into a live map, alerts and trip history.

2G GSM, 4 bandsLight + shake tamper sensorsRelay fuel / power cutPort 11817
SEEWORLD S06A GPS tracker, a slim black box with a bundle of coloured wires coming out of one end
10 sdefault upload interval
300 mAhbuilt-in battery
9 to 90 Vinput voltage
< 10 mlocation accuracy
IP65dust and water rating
gprs · timer
Speed 52 km/hUpload 10 s
01 · Live tracking · GPRS uploads

A fresh position every 10 seconds

The S06A uses an MTK2503D chip with GPS and GLONASS satellites. Out of the box it uploads its place every 10 seconds over GPRS. You can change that with the TIMER command, with one gap for when the engine runs and another for when it is off. Fleet Scanner draws each truck on the live map and saves the route so you can replay the day.

Latitude / longitude Speed Course TIMER (5 to 18000 s)
GPS fleet tracking software →
lbs · base station
LBS roughGSM Strong
02 · Cell tower position · LBS

Still on the map inside a loading bay

Trucks often park under roofs, in sheds or between tall buildings where satellites are hard to see. SEEWORLD says the S06A also supports LBS, which means it can work out a rough place from the mobile towers around it. Fleet Scanner keeps showing the vehicle in the right area until a clear satellite fix comes back.

LBS GPS fix state GSM signal
sensor · light / vibrationsleepmoving
Light TRIGGEREDArmed ON
03 · Tamper alarms · Built-in sensors

Know when someone opens it up or shakes the truck

The S06A has a light sensor inside its case. If a thief finds it and pulls it out, the sudden light sets off a removal alarm. Its vibration sensor arms itself after ten minutes with no movement. After that, a knock or shake sends a vibration alarm. Both alarms go to the platform and to the SOS numbers, and Fleet Scanner shows them as instant alerts with the place they happened.

Light sensor alarm Vibration alarm Auto arm after 10 min
Real-time fleet alerts →
accelerometer · gyroscopeX -612Y 180Z 990
Hard stopDriver -2 pts
04 · Driving behaviour · Motion sensors

Hard starts, hard stops, crashes and speeding

SEEWORLD fits the S06A with a 3-axis accelerometer and a gyroscope. With them it raises alarms for rapid acceleration, rapid slowing down and collisions. It also warns you when a vehicle goes over its speed limit. Fleet Scanner adds these events to each driver’s record, so you can see who drives gently and who needs a talk.

Rapid acceleration Rapid deceleration Collision Overspeed
Driver behaviour reports →
alarm · sos / power offSOS
SOSPower OFF
05 · Emergency and power · Alarm messages

Help button, cut wires and a weak battery

The driver holds the SOS button for 3 seconds to ask for help. The S06A sends an alarm to the platform and a message to up to three SOS numbers. It also warns you when its main power is cut and when its battery runs low. SEEWORLD notes that a new unit should stay powered for more than 10 minutes first, so the battery has enough charge to send the power off alarm.

SOS Power off Low battery SOS,A (3 numbers)
relay · center number
Fuel CUTSpeed 8 km/h
06 · Remote cut-off · Relay output

Stop the fuel pump from your desk

Wire the relay on the fuel pump’s positive line and the S06A can cut the fuel or power. Only the center number can send the RELAY command by SMS, and the platform can send it too. RELAY,1# cuts the fuel and RELAY,0# brings it back. For safety, the tracker only cuts when it has a good GPS fix and the vehicle is under 20 km/h.

RELAY,1# (cut) RELAY,0# (restore) CENTER,A Below 20 km/h
Vehicle theft protection →
input · white wireDIN1 Ignition ONAIN1 12.4 VDOUT1 Relay OFF
ACC ONPower 12.2 V
07 · Ignition and status · ACC line

Engine on, engine off and a quick health check

The white ACC wire goes to the vehicle’s ignition switch, so the S06A knows when the engine is on and sends an ACC alarm. Fleet Scanner uses that signal to cut each day into trips and count engine hours. The STATUS# command sends back the supply voltage, GPRS link, GSM signal, GPS state and ACC state, which helps when a truck goes quiet.

ACC on / off External power (V) GPRS link STATUS#
Trip planning and trip records →

S06A specifications

Network2G GSM 850/900/1800/1900 MHz, GPRS Class 12, TCP/IP
PositioningGPS and GLONASS on an MTK2503D chip (L1), plus LBS
GPS details32 channels, -165 dBm tracking and -146 dBm acquisition sensitivity, under 10 m accuracy
Time to first fixHot start 1 s or less, warm start under 28 s, cold start 30 s or less
Power supply9 to 90 V DC
Built-in battery300 mAh, continuous working time 2 h (SEEWORLD flyer)
SensorsLight sensor, vibration sensor, 3-axis accelerometer and gyroscope
OtherInternal GSM and GPS antennas, microphone for remote listening, extra Tx/Rx interface, remote (OTA) upgrade
Memory16 Mbit, data storage quantity 600
Size and weight84 x 42 x 16 mm, 57 g, IP65
Working temperature-25 to 75 °C
Fleet Scanner port11817 (TCP)

Specifications can differ between hardware revisions. Check the manufacturer’s datasheet for your exact unit.

How to connect the S06A to Fleet Scanner

  1. Slide the cover down and put in a standard-size 2G SIM with data and SMS. If you want remote listening, the SIM needs voice too.
  2. Wire the 4-core cable: red to power positive, black to ground, white to the ignition (ACC) and yellow to the relay control. Put the relay on the fuel pump’s positive line, plug in the SOS button and the microphone if you use them, and mount the S06A with its GPS side facing out, away from metal.
  3. Send the setup SMS messages. APN,yourapn# sets the internet (use APN,yourapn,user,password# if your SIM needs a login). CENTER,A,yourphonenumber# sets the phone that may use the relay, and SOS,A,number1,number2,number3# sets who gets the alarms.
  4. SEEWORLD’s manual has no SMS command for the server address, so ask SEEWORLD to point the S06A at your Fleet Scanner domain or IP with port 11817. Then send PARAM# and check the Server line in the reply.
  5. Add the tracker in Fleet Scanner by the IMEI that PARAM# sends back. Drive around the block and check that the route, ignition and alarms show up. A steady red and a steady blue light mean it is online with a GPS fix.

SEEWORLD S06A FAQ

Does Fleet Scanner work with the SEEWORLD S06A?

Yes. Once the S06A sends to your Fleet Scanner server on port 11817, you see its live position, ignition, tamper alarms and fuel cut-off on your own server. You also get reports, web and phone apps and the built-in AI agent.

What are the main S06A SMS commands?

Every S06A command ends with a # sign. APN,name# sets the internet, TIMER sets how often it reports and SOS,A adds alarm numbers. CENTER,A sets the phone that may send RELAY,1# to cut the fuel and RELAY,0# to restore it. PARAM# and STATUS# read back the settings and the state, WHERE# and URL# send the position, RESET# restarts it and FACTORY# puts back the factory settings.

How do I change the S06A reporting interval?

Send TIMER,T1,T2#. T1 is the gap in seconds while the engine is on and T2 is the gap while it is off. Both can be 5 to 18000 seconds. SEEWORLD’s example TIMER,10,3600# means every 10 seconds when the engine runs and once an hour when it is off.

What is the difference between the SEEWORLD S06A and S06U?

SEEWORLD says the S06A has the S06U’s functions plus a bigger battery, so it keeps working longer after the vehicle’s power is turned off. SEEWORLD does not list other differences.

How long does the S06A battery last?

The built-in battery is 300 mAh. SEEWORLD’s S06A flyer gives a continuous working time of 2 hours. It is a backup for power cuts, because the S06A normally runs on the vehicle’s 9 to 90 V supply.

Is the SEEWORLD S06A still sold?

Yes. SEEWORLD still lists the S06A on its own website under car GPS trackers. It works on 2G only, so make sure 2G is still switched on in the places your trucks drive.

S06A wired in. Every delivery truck on your own map.

From a single tracker to a mixed fleet across 1,000+ device models: live tracking, alerts, fuel, drivers, maintenance and reports in one self-hosted platform. See it with your own hardware.

Get a free demo

More supported GPS trackers

Specs come from SEEWORLD’s S06A product page and S06A flyer. SMS commands and wiring come from the user manual SEEWORLD links on the S06A page, which is printed for the S06U; SEEWORLD says the S06A has the S06U’s functions. SEEWORLD and S06A are trademarks of Shenzhen SEEWORLD Technology.

Take Control with
Fleet Tracking

Track vehicles in real time, optimize routes, and take full control of your fleet operations.

Free Demo