Skip to content
Fleet Scanner
Hardware integration · Teltonika FMC003

Teltonika FMC003 4G OBD GPS tracker, working inside Fleet Scanner

The Teltonika FMC003 is a 4G OBD GPS tracker that reads data straight from the car maker’s own computer. It uses LTE Cat 1, and it drops to 2G where 4G is missing. You push it into the diagnostic socket under the dashboard and it is ready. Fleet Scanner, running on your own server, shows every car on a live map and turns its data into alerts and reports.

LTE Cat 1 with 2G fallbackOBD no wiringOEM data odometer and fuelBluetooth sensors and setup
Illustration of the Teltonika FMC003 GPS tracker
0cables to run
32standard OBD values
33satellite channels
170 mAhbackup battery
128 MBrecord memory
live_position · LTE
LTESpeed 61 km/h
01 · Live tracking · GNSS + LTE Cat 1

A 4G GPS tracker that keeps its trips safe

The FMC003 hears GPS, GLONASS, Galileo and BeiDou satellites on 33 channels. Teltonika rates its position at under 3 metres. It sends each record over 4G, or over 2G in places with no 4G. If the signal drops, its 128 MB memory keeps up to 422,400 records until it can send them. Fleet Scanner draws every trip so you can play it back later.

Position Speed Ignition Satellites in view Stored records
GPS fleet tracking software →
oem_data · OBD
Odometer 112,480 kmFuel 44 %
02 · OEM car data · OBD socket

FMC003 OBD tracker with the real odometer and fuel level

Most plug-in trackers guess how far a car has gone. The FMC003 can ask the car for the number on its own dashboard, and for the true fuel level too. Teltonika calls this OEM data and keeps an online list of more than 1,200 cars that share it. On top of that it can read up to 32 standard OBD values. Fleet Scanner uses these numbers for service reminders and fuel reports.

389 OEM total mileage390 OEM fuel level Standard OBD values
Preventive maintenance scheduling →
driving · motion sensorX -612Y 180Z 990
Hard stopScore -3 pts
03 · Driver behaviour · Accelerometer

Green driving, speeding and crash events

A motion sensor inside the FMC003 feels hard starts, hard stops and fast turns. Teltonika calls these green driving events. It also logs speeding and an engine left running while the car stands still. After a crash it can keep a short trace of the forces from just before and just after the hit. Fleet Scanner adds the events up into a score for every driver.

Green driving Over speeding Idling Crash detection Crash trace
Driver scorecards →
security · scenarios
UnpluggedBackup ON
04 · Theft alerts · Scenarios

Told at once if it is pulled out, towed or jammed

Anyone can pull a plug-in box out of its socket, so the FMC003 watches its power supply. In simple mode it looks only at the voltage. In advanced mode it also checks the motion sensor. It can report a tow while the engine is off, and a jammer blocking the mobile signal. Its backup battery keeps it awake long enough to send the news. Fleet Scanner passes each alert to the right person.

Unplug detection Towing detection Jamming detection
Real-time fleet alerts →
bluetooth · 4.0
Cargo 6 °C
05 · Bluetooth · Bluetooth 4.0

Bluetooth sensors, a scanner and setup from your phone

The FMC003 has Bluetooth 4.0 built in. It can take readings from a wireless temperature and humidity sensor, other BLE sensors and an Inateck barcode scanner. You can also change its settings over Bluetooth with Teltonika’s FMBT phone app, so no laptop is needed in the car park. Fleet Scanner saves every sensor reading next to the trip it came from.

Temperature and humidity sensor Universal BLE sensors Inateck barcode scanner
Fleet reports and dashboards →
ignition · sleep12.6V
Ignition RPMSleep OFF
06 · Ignition and sleep · System settings

Engine on from three sources, and four sleep modes

The FMC003 can decide that the engine is running in three ways: from movement, from the power voltage, or from engine RPM read over OBD. That keeps trips and idling times right in cars where one source is unreliable. When a car stands for a long time, it can rest in GPS Sleep, Online Deep Sleep, Deep Sleep or Ultra Deep Sleep to save the car battery. Fleet Scanner keeps the last known position on the map.

Ignition source External voltage Engine RPM Sleep mode
Trip records →

FMC003 specifications

NetworkLTE Cat 1 with 2G (GSM) fallback; LTE bands depend on the order code
SatellitesGPS, GLONASS, Galileo, BeiDou, SBAS, QZSS, DGPS and AGPS; 33 channels, -165 dBm tracking
Accuracy and startUnder 3 m; hot start under 1 s, warm under 25 s, cold under 35 s
AntennasInternal high-gain GNSS and mobile antennas
Power10 to 30 V DC from the OBD socket, overvoltage protection
Backup battery170 mAh, 3.7 V (0.63 Wh)
Car protocolsISO 9141-2, ISO 14230-4 (KWP) and ISO 15765-4 (CAN)
ExtrasBluetooth 4.0, accelerometer, Micro-USB, navigation and status LEDs
Memory128 MB flash, up to 422,400 records
SIMMicro-SIM
Size67.2 x 49.6 x 25 mm
Fleet Scanner port11922

Specifications can differ between hardware revisions. Check the manufacturer’s datasheet for your exact unit.

How to connect the FMC003 to Fleet Scanner

  1. Lift the FMC003 cover with a plastic pry tool. Slide in a Micro-SIM that has mobile data, with the PIN request turned off and the cut corner going in first.
  2. For FMC003 setup by SMS, text the tracker this line, starting with two spaces: " setparam 2001:your.apn;2002:;2003:;2004:your.server.com;2005:11922;2006:0". 2001 is the APN, 2002 and 2003 are the APN login and password (leave empty if none), 2004 is your Fleet Scanner server, 2005 is the port and 2006:0 picks TCP. You can set the same fields in the Teltonika Configurator over Micro-USB or Bluetooth.
  3. Push the tracker into the OBD socket, which is usually under the dashboard. In Fleet Scanner, add it by its IMEI number and link it to the vehicle.
  4. Turn on the engine and drive around the block. The car should move on the live map. To see the real odometer and fuel level, set the OEM values to on (Low priority) in the OBD settings if your car is on Teltonika’s list.

Teltonika FMC003 FAQ

Can I connect a Teltonika FMC003 to Fleet Scanner?

Yes. Point it at your own Fleet Scanner server on port 11922 using TCP. It speaks Teltonika’s own protocol (the Codec 8 family). Fleet Scanner then shows its position, ignition, OEM odometer and fuel level, driving events, theft alerts and Bluetooth sensor data.

Which FMC003 SMS commands are useful?

Begin each text with two spaces if no SMS login and password are set. "getgps" sends back the current GPS data, date and time. "getver" returns the firmware version and IMEI. "getinfo" gives runtime details, "readio" followed by an ID reads one value, and "cpureset" restarts the tracker. Texts do not get through while it is in Deep Sleep.

Is the FMC003 still sold, and what does it replace?

Yes, it is current. It is not on Teltonika’s end of life list. That list names the FMC003 as the replacement for two older plug-in trackers, the 4G FMC001 and the 2G FMB002.

Will the FMC003 read the real odometer in my car?

Only if your car shares that data. Teltonika keeps a list of more than 1,200 supported cars. If your model is not on it, the tracker can still read the standard OBD values your car shares.

FMC003 in the socket. Real odometer on your own server.

From a single tracker to a mixed fleet across 1,000+ device models: live tracking, alerts, fuel, drivers, maintenance and reports in one self-hosted platform. See it with your own hardware.

Get a free demo

More supported GPS trackers

AVL IDs 389 and 390 are from Teltonika’s OEM parameters wiki page, which lists the FMC003; other data items are named only. OEM data depends on each car. Teltonika and FMC003 are trademarks of Teltonika Telematics. Specifications from the Teltonika FMC003 product page, quick manual v1.3, flyer and wiki.

Take Control with
Fleet Tracking

Track vehicles in real time, optimize routes, and take full control of your fleet operations.

Free Demo